Infrared Top Scan Sensor For Automatic Swing Door Operator
video
Infrared Top Scan Sensor For Automatic Swing Door Operator

Infrared Top Scan Sensor For Automatic Swing Door Operator

Infrared Top Scan Sensor For Automatic Swing Door Operator Production Introduction Can accurately detect the moving or fixed human body and objects, avoid all kinds of rotating automatic sensing door or swing door from colliding with body or objects, to ensure the safety of people and equipment,...

  • Fast Delievery
  • Quality Assurance
  • 24/7 Customer Service
Product Introduction

Infrared Top Scan Sensor For Automatic Swing Door Operator

Production Introduction

Can accurately detect the moving or fixed human body and objects, avoid all kinds of rotating automatic sensing door or swing door from colliding with body or objects, to ensure the safety of people and equipment, widely used in automatic revolving door safety presence occasions.

227-02

Highlight

1,  It can detect moving or standing people or objects, keep safety when people or equipments enter from rotation door or automatic swing door.

2,  Ingenious structure, simple but modern appearance. And very easy to instal.

3,  The detection height and sensing area are adjusted by adjusting wheel and locking the screws, quickly and accurately.

4,  The system has strong pressure stability, with background and noise filtering system, not affected by environment (such as sunshine, snow, rain, etc).

5,  The detection angle of scanning can be accurately adjusted by mounting bracket.

Parameters

Scan area setting

Mechanical adjustment of wheels 500-2800mm

Triangle principle

Ambient temperature

-20~+60

Deviate from set scan area 60

Detection area diameter

About 75mm light spot

Apply in 2000mm scan area

Type of ray

Infrared ray

880nm pulse modulation infrared light

Operation voltage

AC/DC12~36V


Current consumption

<100mA


Signal output

Relay, switch point

Electrical isolation


Highest alternating voltage DC/AC48V

Highest alternating current DC/AC 0.5A

Highest alternating capacitance 55volt-ampere/24watts

 

Rated current (resistive load) DC1A/24V

Inductive load/capacitive load, provide EDM quenching

Resistive load

Detection response time

100ms


Operation mode

Motion or standstill mode

Self-adaption

Function Indicator

LED indicators

Blue light in standby state, red light in detecting state

Housing material

AL/ABS7


Dimensions

750x31x20mm, 620x31x20mm,

900x31x20mm, 1200x31x20mm(optional)

Length/width/height

Production Overview

①Aluminum housing

②Sensor*2

③End cover*2

④Front cover(filter glass)

⑤Mounting brackets*2

⑥Cross-recessed screws*2

⑦Connection terminal

⑧Indicator light

⑨Background set switch

⑩Scanned area regulating wheel 

⑪Transmit cabin

⑫Receive cabin

⑬Wire interface*2

M-227-1

Installation

1, Option1: Remove the two screws from mounting bracket, then push them to another side.

Option2: Remove the screw. Then take the bracket holder and sensor out from aluminum case carefully.

2, Install the aluminum case on the door leaf

3, The screws must be removed before connect the mounting brackets to main case. Put the sensor into case and tighten the 2 mounting brackets to sensor.

NOTE: Install the cable. Make sure the screws are opened from mounting brackets before put the sensor into case.

4, Background mode: Normal or Dark

227-8

5, Start the sensor after finish all installation. Use a piece of paper(A4 or 8.5*11 inch) or your hand to test the detection area.

NOTE: The LED light will from blue turn to red.

6, Use adjusting wheel adjust scan area. Set the scanning range to 25cm above the ground. 

7, Slide the sensor to adjust the detection area (Mounting bracket should be opened).

8, Use the ratchet pawl in mounting bracket to set angle of Inclination. (Note: Adjust the two sides angle to be same to avoid inclination.)

9, After finish all settings, lock the screws in mounting bracket tightly to stabilize the sensor.

10, Close the front cover and use the screw to fasten. After finishing the installation of sensor, put the front cover onto aluminum case.

227-9

All the steps are used for adjustment of single sensor, double or more sensors also use same method.

Troubleshooting

Symptom

Cause

Method

Door open only at a particular point in

time or only open partial.

The scan area has be set too close from floor

Reset the scan area according to the manual sheet.

Door open LED turn red long time.

The scan area has be set too close from floor

Reset the scan area according to the manual sheet.

Sensor always detecting.

Fluorescent lamp is near to the sensor.

Change the angle of Inclination according to the manual sheet.

Remove the fluorescent lamp.

Sensor can not detect moving things.

The scan area has be set too far from floor.

The wire connected between sensors is incorrect. Be caught in the rain.

Reset the scan area and check the wire connection again.

Change the sensor

Q&A

Q1, Could you give me a brief introduction about your company?

A1: Shenzhen Winfor Canbo Co.,Ltd, we are a competitive manufacturer of AUTOMATIC DOOR ACCESS CONTROL ACCESSORIES in China, including motion and presence sensors, touchless switch, attendance access control kit, smart locks, and so on. We have 15 years experiences and 6 production lines, good quality, rich research & develop and product experience, and all CANBO products with CE certification. Support LOGO customization and function customization.

1

Q2, Are there in stock?

A2: Small quantities of stock, large quantities need to order materials, 1000-3000pcs about 10-15 days production period.


Q3. How to delivery?

A3: We support express delivery, by air, by sea, etc. Or if you have your own express payment account,or your own forwarder, please let us know.

Hot Tags: infrared top scan sensor for automatic swing door operator, China, suppliers, manufacturers, factory, customized, wholesale, price, quotation, in stock, free sample, active beam infrared detector, Presence Sensor, beam scan sensor, top scan light spot sensor, rotating door safety detector, through beam sensor

You Might Also Like

(0/10)

clearall